Electronic Spices Solar for DIY Square Shape Mini Solar Panel 6V-100 mAh (70 x 70 x 03 mm)
₹57.00
Electronic Spices Solar for DIY Square Shape Mini Solar Panel 6V-100 mAh (70 x 70 x 03 mm),
- Working models of science projects kits
- Solar panel for science experiment kit to make working models / projects
- Solar power experiments
,
Specification: Electronic Spices Solar for DIY Square Shape Mini Solar Panel 6V-100 mAh (70 x 70 x 03 mm)
|
8 reviews for Electronic Spices Solar for DIY Square Shape Mini Solar Panel 6V-100 mAh (70 x 70 x 03 mm)
Show all
Most Helpful
Highest Rating
Lowest Rating
Add a review
Related Products
Electronic Spices Solar for DIY Square Shape Mini Solar Panel 6V-100 mAh (70 x 70 x 03 mm)
₹57.00
⚡ Pushpendra Singh Patel ⚡ –
For our small project it’s a excellent product. I tested it in tubelight at that time it shows more than 2 volts. In good sunlight it reaches 5.6volt. good one.
senthil –
Useful for my kid
Jitendra Singh –
This solar panel is good. And we want to remove the plastic outcover which is covered on the solar panel so that it works good. We want to keep it under sun for 1 or 2 min then it works efficiently. When attach motor with it, it doesn’t runs we want to rotate the motor then only it starts working. And good product in this rate. But the thing is the base of the solar panel is plastic so it’s a hard challenge to solder where the plastic melts.
Saumen –
I was looking for a solar panel for DIY projects and this looked great, as far as display images go and the price point. So, I went ahead and ordered two, but was disappointed once I opened the packet.
🎁 INSIDE BOX
•••••••••••••••••••
1x Solar Panel (without any soldered connection wire)
➕ PROS
••••••••••••
1. Works well and provide good generation during full sun (up to 6.5 volt based on intensity of sunlight)
2. Current rating is suited for light work (glowing LEDs etc), and cant handle motor kind of equipment directly.
e.g., 1.5v DC motor will need ~0.2 amp current while this can only provide 0.1 amp at peak exposure. So, you will need to connect a few panels in parallel and have voltage regulator in place to run the motor.
3. Front is transparent plastic and comes laminated initially
➖ CONS
••••••••••••
When I opened the package, doubts that arose basis issues faced by others as well came true. I also have the primary issue with the quality of the panel and you could see cost cutting everywhere. This panel has two primary issues:
1. Back and front, both are made of plastic, so it will be a challenge to solder/desolder connection wire to the back. Plastic will melt. It should ideally have been fiberglass.
2. Connection terminals are mere flimsy flat wires coming out of plastic back, which may break even during testing, forget about long term usage. It would be difficult to solder it as well. You don’t have copper soldering points on fiberglass, which are durable.
✍ FINAL VERDICT
••••••••••••••••••••••••
I will not recommend this product for the cons mentioned above, as those simply defy its utility. You will need be extremely carefull with the usage and even with that you may end up rendering it useless after a few cycles.
Placeholder –
nice charging with low price
Kala –
You can only glow a very s. All light from it
Arun –
Badest
Arun –
It looks like the product quality has improved greatly as of Jan 2024. The defects mentioned in earlier reviews have gone away. There are copper terminals for soldering on to. The backplate is heat resistant material similar to a PCB. (See photos)
Tested the panel with wires soldered on and I’m getting around 6v 100mA as promised. (See photos)
Planning to buy a few more of these. Will update this review if I see any quality issues.